It is currently Thu Oct 31, 2024 4:42 pm

All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 22 posts ]  Go to page 1, 2  Next
Author Message
Offline
 Post subject: Making a white maple goban
Post #1 Posted: Sun Jan 06, 2019 10:13 am 
Beginner

Posts: 14
Liked others: 17
Was liked: 14
Rank: 5k OGS
OGS: brose
Here is how I made my portable 19x19 goban after not being able to find a solid wood board without hinges for sale.
This is a list of things used, besides all the tools for planing (if necessary), cutting, and drilling the boards.
  • white maple
      The wood I decided to use. The white maple board ended up about 19 mm thick. The board dimensions for each of the two pieces were 227.3 mm x 424.0 mm for an overall board size of 454.6 mm x 424 mm. There is a 14 mm boarder and the line spacing is 23.7 mm and 22 mm for the shorter side.
  • 1/4 inch dowels
      The dowels used to hold the two halves together are 1/4 inch, these are just held by pressure and are removable by hand. (note: my latest version uses mangets instead of dowels to hold the halves together)
  • pen/marker
      I did some test runs of a standard Sharpie (fine point), Sharpie (ultra fine point), Sharpie pen, Staedtler Lumocolor F, Staedtler Lumocolor Special F. I would not use the Sharpie pen and the ultrafine point, other than that it sort of seems personal preference. I liked the look of the Staedtler Lumocolor Special F best and used that.
  • drill gauge/drill index
      For making star points that are about 4 times larger than the line thickness.
  • General Finishes High Performance Water Based Topcoat, Flat
      I highly recommend this exact finish. It is a urethane/acrylic blend. Whatever you use, make sure it is water based to avoid potential ink bleeding problems with oil based finishes.
  • 18" ruler
      A 18 inch steel ruler with cork backing. The cork backing is somewhat important to prevent ink bleeding. See the image below for details.


Here is what I did to make the boards,
  1. The first steps are planing, cutting the boards, drilling holes for dowels, and then sanding until level, starting with about 80 grit and working up to about 220 grit.
  2. Next, a moderate layer of the water based finish is applied and allowed to dry for a day or two. Some water was added to the finish to thin it out a bit, since the goal of the first coat is to fill the wood grain and block it from causing the ink to bleed.
  3. A very light sanding just to smooth the finish for drawing lines using 320 grit sandpaper.
  4. The grid line locations were marked with pencil, about 1 cm marks near the outside border of all sides.
  5. The outside box was drawn. Extensive use of painters tape was used to cover where the end of the lines are. It also provided the benefit of testing where the ruler and pen would make a line. The nice part about having the coat of polyurethane applied is that mistakes can be 'erased' use a razor knife or hobby knife.
  6. The inside grid was drawn and let sit for a day.
  7. Two more light coats of polyurethane were applied and let dry for a day or two.

Images of the board and other things

I plan on making another soon with the leftover wood.


Last edited by MagRes on Sun Nov 29, 2020 4:16 pm, edited 3 times in total.

This post by MagRes was liked by 8 people: Bonobo, cobrahc, EdLee, Elom, fireproof, schwartzseer, Waylon, wind&water
Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #2 Posted: Sun Jan 06, 2019 11:00 am 
Lives in gote

Posts: 389
Liked others: 81
Was liked: 128
KGS: lepore
Wow gorgeous work. I envy your craftsmanship.

Question - I understand maple is a very hard wood, and wonder about the sound and feel as stones are placed on the board. Katsura, by contrast, is so soft that it not only mutes the sound, but creates dents when the stones slapped down on it over time.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #3 Posted: Sun Jan 06, 2019 1:04 pm 
Gosei

Posts: 1628
Liked others: 546
Was liked: 450
Rank: senior player
GD Posts: 1000
Most of the traditional go board woods are somewhat soft, e.g. katsura, kaya, hiba, hinoki, spruce, agathis. I suspect that somewhat soft wood is desirable because it cushions the fingers when the stones are "slapped" down. I've heard that clam shell stones can break if played energetically on a hard wood. I've never noticed it myself, but my own boards are made from katsura, kaya, and hiba.

Very nice craftspersonship! I guess it would be hard to find quarter-sawn wood. The wood for masame (straight grain across the playing surface) is quarter-sawn.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #4 Posted: Sun Jan 06, 2019 6:33 pm 
Beginner

Posts: 14
Liked others: 17
Was liked: 14
Rank: 5k OGS
OGS: brose
Thanks.

I am no expert on aesthetics and tend to be a bit more utilitarian oriented, but I still like things that are nice. I use glass or yunzi or plastic stones, so I am not worried about slate or shell issues. I went with a slightly harder wood because I intend this to be a portable board and get thrown in bags and places with things that can potentially dent and scrape the wood. Soft woods would get torn up a bit faster. Maybe if I make another set beyond these two I will use something a bit softer, but finding decent stock can be an issue. Overall I am quite happy with the white maple and I liked the muted grain.

Top
 Profile  
 
Offline
 Post subject:
Post #5 Posted: Mon Jan 07, 2019 1:04 pm 
Honinbo
User avatar

Posts: 8859
Location: Santa Barbara, CA
Liked others: 349
Was liked: 2076
GD Posts: 312
Congrats. And happy 2019.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #6 Posted: Thu Jan 17, 2019 9:55 am 
Dies with sente

Posts: 70
Liked others: 17
Was liked: 23
Rank: cn 3d
I love this wood colour! And you worked it wonderfully! I own multiple go sets, one is bamboo which is very hard wood but which stay without scratches for life... But I like the light colour of your board more, the bamboo is a bit too dark.
Smooth woods have their advantages for sure but in my way of life durability stay first as a must.

Great job

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #7 Posted: Fri Jan 18, 2019 2:51 pm 
Lives in sente

Posts: 1040
Liked others: 0
Was liked: 182
gowan wrote:
Most of the traditional go board woods are somewhat soft, e.g. katsura, kaya, hiba, hinoki, spruce, agathis. I suspect that somewhat soft wood is desirable because it cushions the fingers when the stones are "slapped" down. I've heard that clam shell stones can break if played energetically on a hard wood.


Yes, the Asian boards were traditionally made from "soft woods". And maple is not only a "hard wood". It is a hard "hard wood". But just like there are rather hard "soft woods" (yellow pine, hemlock, etc.) there are relatively soft "hard woods".

If making a go board from a local "hard wood" perhaps something like "poplar"? Lots of other possibilities. Would "tulip tree" be suitable? Those might be available is large size.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #8 Posted: Sat Jan 19, 2019 1:00 am 
Dies with sente

Posts: 70
Liked others: 17
Was liked: 23
Rank: cn 3d
I would be surprised to find a wood harder as bamboo

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #9 Posted: Sat Jan 19, 2019 10:01 am 
Lives in gote

Posts: 418
Liked others: 9
Was liked: 83
Rank: kgs 5 kyu
KGS: Pio2001
Very nice job !

If you plan to make another one, try to find a black pigment ink, like India ink, because the black ordinary ink of your pens might fade.

Also, I am a bit surprised to see that white maple is hard. I've got a collection of mechanical puzzles in wood, and the ones in maple are the softest. Softer than oak, cherry, plum, or walnut.

Vio wrote:
I would be surprised to find a wood harder as bamboo


I don't have bamboo puzzles, but I've got go bowls in bamboo. Yes, it looks hard. But if you want a harder wood, try ipe !

Edit : of course ipe is too dark to make a go board. If you're looking for a tough, yet not too hard white wood, a good candidate would be hornbeam. But Maple is more beautiful.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #10 Posted: Mon Jan 21, 2019 12:28 pm 
Gosei

Posts: 1628
Liked others: 546
Was liked: 450
Rank: senior player
GD Posts: 1000
White maple is not a usual botanical description of a maple species. Most maple looks white when it has not been exposed to sunlight. Various species have different hardness. "Red" maple is softer than "rock" maple, for example. The meaning of hard or soft comes from whether the tree is deciduous or a conifer, not from how easily it is to dent the wood from pressure. Wood workers, such as carvers or turners think red maple is easier to carve or turn, while rock maple is a pain to carve. No one has mentioned that maple darkens on exposure to light, going from white to brownish. If a brown cast to the board is not unpleasant then your maple go board will be fine. Personally I find white maple to look raw but the color is pleasant after it is exposed to sunlight for a while. Many species of wood darken that way, e.g. maple, cherry, pine.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #11 Posted: Mon Jan 21, 2019 1:39 pm 
Lives in gote

Posts: 418
Liked others: 9
Was liked: 83
Rank: kgs 5 kyu
KGS: Pio2001
I see.

The soft maple I've got is called sycamore maple. It is often waved. I think that it is the same that is used for music instruments.
I have owned it for 6 years, with moderate exposure to daylight, without direct exposure to sunlight. It has barely darkened. It can only be seen because some parts of the wood are protected from ambient light and are a bit whiter.

Top
 Profile  
 
Offline
 Post subject:
Post #12 Posted: Mon Jan 21, 2019 3:45 pm 
Honinbo
User avatar

Posts: 8859
Location: Santa Barbara, CA
Liked others: 349
Was liked: 2076
GD Posts: 312
Quote:
...sycamore maple. It is often waved.
Waved means warped, or to have wavy grain patterns ?

Top
 Profile  
 
Offline
 Post subject: Re:
Post #13 Posted: Mon Jan 21, 2019 5:25 pm 
Lives with ko
User avatar

Posts: 172
Location: Santa Barbara, CA
Liked others: 235
Was liked: 77
Universal go server handle: fireproof
EdLee wrote:
Quote:
...sycamore maple. It is often waved.
Waved means warped, or to have wavy grain patterns ?


Perhaps something like this :
[inline-hide]Image[/inline-hide]

It's caused by the weight of the tree itself as it grows, I believe.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #14 Posted: Mon Jan 21, 2019 6:44 pm 
Dies with sente

Posts: 70
Liked others: 17
Was liked: 23
Rank: cn 3d
Is there some way to protect from the darkening? I guess applying some onguent maybe although I doubt it works as long as you need to play with light?

And what about Sequoia? Seems to be easier to make a full thick with a nice cut. Is it too rare, or too dark?

Top
 Profile  
 
Offline
 Post subject: Re: Re:
Post #15 Posted: Tue Jan 22, 2019 4:58 am 
Lives in gote

Posts: 418
Liked others: 9
Was liked: 83
Rank: kgs 5 kyu
KGS: Pio2001
fireproof wrote:
Perhaps something like this :


Yes, exactly.

Top
 Profile  
 
Offline
 Post subject:
Post #16 Posted: Wed Jan 23, 2019 3:16 pm 
Honinbo
User avatar

Posts: 8859
Location: Santa Barbara, CA
Liked others: 349
Was liked: 2076
GD Posts: 312
Quote:
Is there some way to protect from the darkening?
Avoid harsh, direct sunlight ?

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #17 Posted: Thu Jan 24, 2019 9:45 pm 
Gosei

Posts: 1628
Liked others: 546
Was liked: 450
Rank: senior player
GD Posts: 1000
The "wave" in the grain is known as flame. I is found in many types of wood and is caused by growth conditions. Usually it is highly valued for furniture or musical instrument making. Personally I think it might be too distracting for a go board. Of course all of those issues of appearance are matters of taaste.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #18 Posted: Fri Jan 25, 2019 2:19 am 
Dies with sente

Posts: 70
Liked others: 17
Was liked: 23
Rank: cn 3d
I played many games in real life, can't estimate it. I played on many kind of boards usually on the normal size but may have been some in bad state, some grey plastic...

I can say I was NEVER distracted by how the board is. For sure.
So for me you can just focus on having a nice looking and comfortable board and not worry that much on lines, shapes or scratches disturbing your gameplay.

Back on OP goban picture, I find it awesome. The yunze stones match so well the board material, gave me a "modern" feeling and is as good as a Asian esthetic more yellowish. My taste only of course.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #19 Posted: Fri Jan 25, 2019 10:11 am 
Beginner

Posts: 14
Liked others: 17
Was liked: 14
Rank: 5k OGS
OGS: brose
Pio2001 wrote:

If you plan to make another one, try to find a black pigment ink, like India ink, because the black ordinary ink of your pens might fade.



I really wanted to do this initially, but getting uniform lines was going to be extremely difficult. The fillable pens/markers I could find for pigmented ink make lines that are to thick and not uniform. I don't really want to use a sword or knife to do it, because a large jig would be needed and I'm not making more than a few for fun.
Ultimately, if it does fade, it is about a half-day job to remove the old lines and finish and reapply the new lines and finish. The Staedtler Lumocolor Special marker I used should last quite a while. It is advertised as "Extremely lightfast (on smooth surfaces: black for 7 years; on paper considerably longer)." I would think it would last at least 10-20 years even if exposed to light since it is somewhat protected with the finish.

Top
 Profile  
 
Offline
 Post subject: Re: Making a white maple goban
Post #20 Posted: Sun Feb 10, 2019 3:38 pm 
Lives in gote

Posts: 418
Liked others: 9
Was liked: 83
Rank: kgs 5 kyu
KGS: Pio2001
I have found a site with a lot of information on woods :
https://www.wood-database.com/wood-arti ... oft-maple/

It confirms what Gowan told us, and gives a measurement of the hardness of many woods.

Hard maple (or rock maple) has a Janka hardness of 1,450 lbf, while soft maples have a hardness around 800 lbf only. That explains why my maple looks soft, while yours looks hard.
Bamboo's hardness is similar as hard maple's, around 1500 lbf.

But many tropical woods are harder than that. I talked about ipe. I was not mistaken, its hardness is 3500 lbf ! More than twice as hard as hard maple and bamboo.

The hardest known wood is lignum vitae, with a hardness of 4390 lbf. I once had a small puzzle made of lignum vitae in hand. It was so heavy and hard that I could have mistaken it for a kind of stone !

Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 22 posts ]  Go to page 1, 2  Next

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group